1982 AMC Eagle SX4 West Fargo ND - Motivated seller - Price Drop

[xtreamedrtbker]

Selling my AMC Eagle SX/4. I have my own business and there is no time for this project. This car is a project car, but everything that has been done was done very well.

1982 SX/4, 5 speed with factory CB radio and sun roof. I have pulled the engine and front axle to prep the car for the engine that will be included in this sale.

Engine specs. -
1995 Jeep stroker engine 4.6L new, rebuild never ran.

1995 Jeep 4.0 block all machine work and bottom end assembly by Quality engine in Fargo.
Bored with Icon/KB forged 944 stroker pistons
4.0 rods with ARP bolts
258 (4.2) crank turned .010/.010
Block milled to zero deck
Mopar performance steel head gasket
ARP Head Bolts
New valves, springs and keepers, all work done by Quality engine in Fargo.
7120 casting number head, the better of the factory heads.
High lift valve springs from 505 performance
Chrome-moly pushrods from 505 performance
Comp camshaft 250H-11, spec listed below
New harmonic balancer.
Includes new flywheel for a 95 jeep that is balanced to the crank.
Includes Felpro oil pan gasket, but no oil pan.
Factory intake included, cleaned and ready to assemble.
No distributor
New water pump

Cam Style:Hydraulic flat tappet
Basic Operating RPM Range:800-5,000
Intake Duration at 050 inch Lift:206
Exhaust Duration at 050 inch Lift:214
Duration at 050 inch Lift:206 int./214 exh.
Advertised Intake Duration:250
Advertised Exhaust Duration:258
Advertised Duration:250 int./258 exh.
Intake Valve Lift with Factory Rocker Arm Ratio:0.462 in.
Exhaust Valve Lift with Factory Rocker Arm Ratio:0.485 in.
Valve Lift with Factory Rocker Arm Ratio:0.462 int./0.485 exh.

Cost to build engine was $3,000 including the cost of the engine I started with.

The bell housing has been machined by Novak Adapters for a crank sensor so you can used factory 4.0 EFI. The Eagle oil pan, engine mounts and axle mounts are powder coated and ready to install. Engine bay has been painted silver and currently brake master cylinder and brake booster are removed because of the paint. The wheels and tires are new with only 1200 miles on them. General grabber AT2 with Ultra brand aluminum wheels (about $1000 retail for the set). New rear leaf springs installed and includes new front coils. I can get more information and more current photos for a serious buyer. Engine not installed currently. Located in West Fargo, ND. $2500 I'd like to see a Amc Eagle fan fish this car.  I gave over 5k into this car over the last couple of years and hate to see it parted out.

*** May take trade for a  pre 1993 dodge 4x4 pickup or pre 1979 Ford 4x4 pickup. 4x4 Japanese mini truck. Also motorcycles, anything that is worth while I would consider.  ***
Photo of the day I pulled the original engine.



See link for more photos.
https://www.dropbox.com/sh/ytpzngmjwjp8v5g/AAAMutmLzuvcPnybTKlLR-T5a?dl=0

[xtreamedrtbker]

Will take a reasonable offer from a serious buyer. Could be a great car, just don't have the time or space. Send a text or give me a call. Joe - 701-630-0640

[xtreamedrtbker]

Engine is worth more than my asking price.  Need room, must go.

[Prafeston]

Wish this was closer!

[mo.eagles]

Wish this was closer!

Same here  !!!

[xtreamedrtbker]

For how cheap I'm willing to let it all go for to a AMC Eagle fan, its worth the drive.

[priya]

Wish this was closer!

It is closer to me.  If I didn't have my restored SX/4 I'd jump on this.

[xtreamedrtbker]

For a AMC Eagle Den member there is a very good "buy it now price"....

Updates- dropped to $2,500 for everything. Will part if it doesn't sell. Very solid car, just surface rust.

[70challenger70]

Still for sale?  If so... I'm interested...

[vangremlin]

Still for sale?  If so... I'm interested...

The seller hasn't been on the site in a couple weeks.  You may want to send him a Direct Message or an email to get a quicker response.  Good luck!

[xtreamedrtbker]

Car and engine sold. Went to someone who is planning to finish the project which is great! Thanks everyone!

[Prafeston]

They going to join the forum? Would love to see it finished.

[rab7x]

Very late reply, but I own this awesome Eagle now. Finally have the funds and time to work on it!

[Prafeston]

Glad the new owner joined us here! I so wished I could have grabbed this!