News: Putting FUN and FRIENDLINESS, FIRST into owning and learning about AMC small bodied cars, primarily Eagles, Spirits and Concords as well as vehicles built in AMC's Mexican subsidiary, VAM.

The AMC Eaglepedia can now be accessed using the buttons found below  This is a comprehensive ever growing archive of information, tips, diagrams, manuals, etc. for the AMC Eagle and other small bodied AMC cars. 

Also a button is now available for our Face Book Group page.


Welcome to the AMC Eagles Nest.  A new site under "old" management -- so welcome to your new home for everything related to AMC Eagles, Spirits and Concords along with opportunities to interact with other AMC'ers.  This site will soon be evolving to look different than it has and we will be incorporating new features we hope you will find useful, entertaining and expand your AMC horizons.

You can now promote your topics at your favorite social media site by clicking on the appropriate icon (top upper right of the page) while viewing the topic you wish to promote.


  • October 04, 2024, 10:53:53 PM

Login with username, password and session length

Author Topic: Flexplate chewed?  (Read 1594 times)

0 Members and 1 Guest are viewing this topic.

Offline Mr_Roboto

  • Eagle
  • **
  • Posts: 62
  • Thumbs Up 2
Flexplate chewed?
« on: July 24, 2022, 10:10:06 PM »
Looking for opinions, workarounds etc. on this. I think it's done and I'm dropping the pan but want to be sure there's not another alternative/I'm not overthinking it.



Offline MIPS

  • Eagle Limited
  • *****
  • Posts: 519
  • Thumbs Up 50
Re: Flexplate chewed?
« Reply #1 on: July 25, 2022, 12:26:09 AM »
Yeah it's getting pretty worn. How has your starter engagement been lately? What does the bendix gear look like?

Offline Mr_Roboto

  • Eagle
  • **
  • Posts: 62
  • Thumbs Up 2
Re: Flexplate chewed?
« Reply #2 on: July 25, 2022, 01:18:03 AM »
Aside from a small chip the bendix actually looks fine.When I try to start it you can tell it hits a compression stroke then just stops and starts spinning. I started pulling the trans tonight. I'm going to do a couple things while I'm in there, so hopefully it won't be too dramatic.

Offline MIPS

  • Eagle Limited
  • *****
  • Posts: 519
  • Thumbs Up 50
Re: Flexplate chewed?
« Reply #3 on: July 25, 2022, 01:45:46 AM »
It's not like 258 flexplates are hard to get or expensive, so if you are dropping the gearbox there's no point leaving that in.

Offline maddog

  • a long haired redneck country boy
  • AMC Eagles Den Addicted
  • ********
  • Posts: 1821
  • Thumbs Up 50
  • AMC Eagle the original crossover
Re: Flexplate chewed?
« Reply #4 on: July 25, 2022, 07:40:45 PM »
Honestly if I were you I would just get a new flexplate.
1998 CHEVY S10 (DAILY DRIVER/PROJECT) INTIMIDATIN'
1980 AMC EAGLE WAGON (PROJECT) EAGLE EYES
http://forums.amceaglesden.com/index.php?topic=30758.0
1983 AMC EAGLE LIMITED WAGON-SURVIVOR (gone)
http://forums.amceaglesden.com/index.php?topic=32372.0

Offline Mr_Roboto

  • Eagle
  • **
  • Posts: 62
  • Thumbs Up 2
Re: Flexplate chewed?
« Reply #5 on: July 26, 2022, 12:20:05 PM »
It's not like 258 flexplates are hard to get or expensive, so if you are dropping the gearbox there's no point leaving that in.

I'm going to do a bunch of "while I'm at it" stuff but the primary reason for dropping the box is to get that out and swapped. I'm sticking a Renix flexplate in and adding a hole for a reluctor as well and tossing in a 4.0 mini starter which is good because I need the clearance for an exhaust project. I may do a stall converter if I can turn it around quick enough.
« Last Edit: July 26, 2022, 01:04:04 PM by Mr_Roboto »

 

SMF spam blocked by CleanTalk