News: Putting FUN and FRIENDLINESS, FIRST into owning and learning about AMC small bodied cars, primarily Eagles, Spirits and Concords as well as vehicles built in AMC's Mexican subsidiary, VAM.

The AMC Eaglepedia can now be accessed using the buttons found below  This is a comprehensive ever growing archive of information, tips, diagrams, manuals, etc. for the AMC Eagle and other small bodied AMC cars. 

Also a button is now available for our Face Book Group page.


Welcome to the AMC Eagles Nest.  A new site under "old" management -- so welcome to your new home for everything related to AMC Eagles, Spirits and Concords along with opportunities to interact with other AMC'ers.  This site will soon be evolving to look different than it has and we will be incorporating new features we hope you will find useful, entertaining and expand your AMC horizons.

You can now promote your topics at your favorite social media site by clicking on the appropriate icon (top upper right of the page) while viewing the topic you wish to promote.


  • March 29, 2024, 06:13:00 AM

Login with username, password and session length

Author Topic: Starter motor dragging  (Read 8075 times)

0 Members and 1 Guest are viewing this topic.

Offline skuhler

  • Eagle
  • **
  • Posts: 24
  • Thumbs Up 2
Starter motor dragging
« on: January 02, 2014, 09:20:41 PM »
I recently did the ECM Test and set the specs on the timing accordingly.  The motor now runs great and idles smooth.  But a problem has cropped up and I don't know if it's related or not.  Usually, the first time I hit the starter, it turns right over and fires within about 2 seconds.  After I've driven for a while, I can park it and when I hit the starter, it drags so hard I'm thinking the battery is dead.  If I stop and try it again, it may drag or it may fire right up.

I thought maybe the starter was bad, so I replaced it.  No change.  Then I changed the solenoid, no change.  I've been looking at the threads and think maybe the timing, but why does it run so well if the timing is so far off?  I'm about out of ideas, anyone?

Offline carnuck

  • Having a 727 means never re-doing the trans again
  • AMC Eagles Den Addicted
  • ********
  • Posts: 3451
  • Thumbs Up 89
  • Near Seattle
    • Virtual Jeep
Re: Starter motor dragging
« Reply #1 on: January 03, 2014, 12:23:15 AM »
Timing about 4 degrees too far advanced will do that to you. If you were lucky you could get the reduction style starter and be done with the Ford "dead short" style.
AMC/Jeep gauges are for amusement only. Any correlation between them and reality is purely coincidental!

Offline skuhler

  • Eagle
  • **
  • Posts: 24
  • Thumbs Up 2
Re: Starter motor dragging
« Reply #2 on: January 03, 2014, 08:13:15 AM »
I'll check that timing again.  Yeah, the starter was off-the-shelf at O'Reilly's.

Offline skuhler

  • Eagle
  • **
  • Posts: 24
  • Thumbs Up 2
Re: Starter motor dragging
« Reply #3 on: January 03, 2014, 03:49:32 PM »
I checked the timing.  It was right on 8 degrees.  I adjusted down to 4 and up to 12 and didn't notice a difference.  I'm wondering if the battery is actually weak.  I'm going to put a charge on it and try again.  Any other thoughts?

Offline IowaEagle

  • AMC Eagle Archivist
  • Administrator
  • AMC Eagles Den Addicted
  • *****
  • Posts: 31968
  • Thumbs Up 476
Re: Starter motor dragging
« Reply #4 on: January 03, 2014, 04:23:35 PM »
You really need good battery cables.  Not those cheap Wal-Mart ones.
Click for Toledo, IA Forecast" border="0" height="100" width="150   


Not a Jeep.  Not a Car.  Its an AMC Eagle!

1982 Eagle SX/4 Sport;
1980 Concord DL;
1970 Ambassador 2 Dr HT, SST
2002 Hyundai Santa Fe;
2008 Jeep Patriot Sport - Freedom Drive II

Offline skuhler

  • Eagle
  • **
  • Posts: 24
  • Thumbs Up 2
Re: Starter motor dragging
« Reply #5 on: January 04, 2014, 01:08:48 PM »
Yes, they look small compared to the ones I use on the farm, the one going from the solenoid to the starter looks original, with the woven fiber covering.  The ground looks original, with a replacement end on it.  I prefer the ones where the end is pressed on at the factory. 

Offline IowaEagle

  • AMC Eagle Archivist
  • Administrator
  • AMC Eagles Den Addicted
  • *****
  • Posts: 31968
  • Thumbs Up 476
Re: Starter motor dragging
« Reply #6 on: January 04, 2014, 02:01:14 PM »
These starters, like all similar Ford starters really like to have solid connections and more than minimal cabling,.
Click for Toledo, IA Forecast" border="0" height="100" width="150   


Not a Jeep.  Not a Car.  Its an AMC Eagle!

1982 Eagle SX/4 Sport;
1980 Concord DL;
1970 Ambassador 2 Dr HT, SST
2002 Hyundai Santa Fe;
2008 Jeep Patriot Sport - Freedom Drive II

Offline Monkeyjoe

  • What greater man is than one who gives his life for his friends
  • Eagle Sport
  • ****
  • Posts: 360
  • Thumbs Up 18
  • If you want to look common, buy a Ferrari
Re: Starter motor dragging
« Reply #7 on: January 05, 2014, 11:21:05 AM »
Yes, they look small compared to the ones I use on the farm, the one going from the solenoid to the starter looks original, with the woven fiber covering.  The ground looks original, with a replacement end on it.  I prefer the ones where the end is pressed on at the factory.

I would look into corrosion or just a dirty connection inside that replacement end.  If you see the insulation bubbled or deformed, the corrosion has traveled up into the cable.  may look innocent but will definitely cause problems.
I JUST TELL MY WIFE "SOME PEOPLE COLLECT STAMPS"
1982 AMC Eagle SX4, (Little Beast)
1983 AMC Eagle Wagon, (Gold Digger)
1992 Dodge, Cummins, 1 Ton Duelly (Big Red)
1967 International Scout 800 (Scooter)
1988 Chevy k1500
1960 Ford F100
1927 Model T, Hotrod(Daddys Girl)
1961 Willys FC150 (Scat)
1978 Honda CB750
1971 Honda CB350

Offline IowaEagle

  • AMC Eagle Archivist
  • Administrator
  • AMC Eagles Den Addicted
  • *****
  • Posts: 31968
  • Thumbs Up 476
Re: Starter motor dragging
« Reply #8 on: January 05, 2014, 11:30:08 AM »
Fresh cables are always a good thing to do.
Click for Toledo, IA Forecast" border="0" height="100" width="150   


Not a Jeep.  Not a Car.  Its an AMC Eagle!

1982 Eagle SX/4 Sport;
1980 Concord DL;
1970 Ambassador 2 Dr HT, SST
2002 Hyundai Santa Fe;
2008 Jeep Patriot Sport - Freedom Drive II

Offline skuhler

  • Eagle
  • **
  • Posts: 24
  • Thumbs Up 2
Re: Starter motor dragging
« Reply #9 on: January 10, 2014, 12:26:56 PM »
Latest update on this curious problem - the 258 continued to drag, so I adjusted the timing to the closest setting I could.  It worked great, almost all the time.  But not always, so I pulled it in the shop one more time to look and hear for some other issue (like a stuck valve, or something).  This time, I didn't have the shop lights on when I opened the hood.  There, on number 5 cylinder, was a spark from the cable to the block.  What?  Upon closer examination, when I replaced the plugs, I must not have slid the protective sleeve all the way down to the insulation on the plug.  It was arcing from the metal wire end to the block.  I slid the sleeve down all the way and the spark disappeared. 

The underhood sticker says to time at 9 degrees +- 4 at 1600 +- 25 rpm.  I'm guessing that still applies, even after the ECM Test.  The trick was getting it to 1600 since I don't have a handheld tach.  I picked up an optical digital tach from the tool store, and it works just fine, tho.

I'm going to drive it some more and check it out, but I'm thinking that since 5 wasn't always firing, it had increased pressure at startup, resulting in the drag.  What do you think?

Sidebar - why would the wire arc to the block?  I've got an old tractor with no protective sleeve on the plug at all, runs great.

Offline IowaEagle

  • AMC Eagle Archivist
  • Administrator
  • AMC Eagles Den Addicted
  • *****
  • Posts: 31968
  • Thumbs Up 476
Re: Starter motor dragging
« Reply #10 on: January 10, 2014, 01:50:09 PM »
Not sure on the tractor, maybe the coil is not as hot as the one on the Eagle, or the plug wire on the tractor has too much resistance.  Grounding out a plug wire will cause a spark.
Click for Toledo, IA Forecast" border="0" height="100" width="150   


Not a Jeep.  Not a Car.  Its an AMC Eagle!

1982 Eagle SX/4 Sport;
1980 Concord DL;
1970 Ambassador 2 Dr HT, SST
2002 Hyundai Santa Fe;
2008 Jeep Patriot Sport - Freedom Drive II

Offline carnuck

  • Having a 727 means never re-doing the trans again
  • AMC Eagles Den Addicted
  • ********
  • Posts: 3451
  • Thumbs Up 89
  • Near Seattle
    • Virtual Jeep
Re: Starter motor dragging
« Reply #11 on: January 10, 2014, 04:29:02 PM »
Are you sure on that 1600 RPM? Mine says 600 RPM in gear.
AMC/Jeep gauges are for amusement only. Any correlation between them and reality is purely coincidental!

Offline IowaEagle

  • AMC Eagle Archivist
  • Administrator
  • AMC Eagles Den Addicted
  • *****
  • Posts: 31968
  • Thumbs Up 476
Re: Starter motor dragging
« Reply #12 on: January 10, 2014, 06:13:13 PM »
Yeah 550 - 600 is about right in drive.
Click for Toledo, IA Forecast" border="0" height="100" width="150   


Not a Jeep.  Not a Car.  Its an AMC Eagle!

1982 Eagle SX/4 Sport;
1980 Concord DL;
1970 Ambassador 2 Dr HT, SST
2002 Hyundai Santa Fe;
2008 Jeep Patriot Sport - Freedom Drive II

Offline Prafeston

  • I <3 Wheels
  • Global Moderator
  • Eagle Turbo Diesel
  • *****
  • Posts: 1461
  • Thumbs Up 55
Re: Starter motor dragging
« Reply #13 on: January 10, 2014, 07:01:58 PM »
How are you supposed to check your timing while in Drive? Especially in a stick shift?
1983 AMC Eagle SX/4 - Penny

Offline carnuck

  • Having a 727 means never re-doing the trans again
  • AMC Eagles Den Addicted
  • ********
  • Posts: 3451
  • Thumbs Up 89
  • Near Seattle
    • Virtual Jeep
Re: Starter motor dragging
« Reply #14 on: January 10, 2014, 07:03:21 PM »
You will note the shifter on a stick has no drive position. :)
AMC/Jeep gauges are for amusement only. Any correlation between them and reality is purely coincidental!

 

SMF spam blocked by CleanTalk